I was setting here thinking of ways to improve UVB strength or back it down a bit. When the thought crossed my mind about using small mirrored tile squares as a reflector. Would it defuse or increase UVB output or would it make no difference????
These things constantly run through my head, LOL!!!
If you've got a Solarmeter or other way to measure the difference, run the experiment!
I've got one of the bad reflectors. I tried messing with aluminum foil in a few ways, but no improvement.
Brandon's doing an experiment with aluminum tape applied to the bad reflectors. If it succeeds, I'll probably try that. I spoze I could jury-rig a couple of angled long skinny mirrors along the sides of the fixture, calculating the angle via vector diagram... :dontknow:
If you've got a Solarmeter or other way to measure the difference, run the experiment!
I've got one of the bad reflectors. I tried messing with aluminum foil in a few ways, but no improvement.
Brandon's doing an experiment with aluminum tape applied to the bad reflectors. If it succeeds, I'll probably try that. I spoze I could jury-rig a couple of angled long skinny mirrors along the sides of the fixture, calculating the angle via vector diagram... :dontknow:
1. Already spent the money on one that was supposed to do the job, and it isn't.
Hate throwing good money after bad.
2. Like this bad one, most are (ostensibly) fine at reflecting white light for plants;
haven't seen one yet specifically for UV that will fit the Sunblaster fixture I already have.
3. Sometimes I like mucking about. :roll: Have since I was knee-high to a lizard.
Does that make me a "mucker"? :lol:
1. Already spent the money on one that was supposed to do the job, and it isn't.
Hate throwing good money after bad.
2. Like this bad one, most are (ostensibly) fine at reflecting white light for plants;
haven't seen one yet specifically for UV that will fit the Sunblaster fixture I already have.
3. Sometimes I like mucking about. :roll: Have since I was knee-high to a lizard.
Does that make me a "mucker"? :lol:
1. Already spent the money on one that was supposed to do the job, and it isn't.
Hate throwing good money after bad.
2. Like this bad one, most are (ostensibly) fine at reflecting white light for plants;
haven't seen one yet specifically for UV that will fit the Sunblaster fixture I already have.
3. Sometimes I like mucking about. :roll: Have since I was knee-high to a lizard.
Does that make me a "mucker"? :lol:
Better off getting a sheet of thin aluminium sheet and giving it a buff on one side .
Highly polished ( ie cerium powder polished ) aluminium is very good , reflecting 92% of UV.
ref Private communications with Newport Glass Works ( Optical Div ).
Not what I'm seeing at all with my own personal tests. I'm getting near 100% increase with standard aluminum foil.
But then again, the source you posted for that is from 1929. So many variables could have changed since then. Measuring equipment, aluminum foil as a whole, etc.
Not what I'm seeing at all with my own personal tests. I'm getting near 100% increase with standard aluminum foil.
But then again, the source you posted for that is from 1929. So many variables could have changed since then. Measuring equipment, aluminum foil as a whole, etc.
The low reflectivity is not from POLISHED aluminium , it's from mill grade surface.
The geometric profile if the reflector is also important, shaped to a parabolic profile with the focus at the source will concentrate the UV where you want it.
More info here : http://scipp.ucsc.edu/~haber/ph5B/parabolic09.pdf compares the properties of spherical and parabolic mirror profiles .
Well aluminum foil isnt milled, it is rolled.
I only bring it up because you made it sound like you shouldn't use foil, that you should buy a sheet of milled aluminum and polish it yourself.
And all I'm saying is that is unnecessary as the aluminum foil you likely have in your cabinets will do just as well without needing to be buffed or polished.
Well aluminum foil isnt milled, it is rolled.
I only bring it up because you made it sound like you shouldn't use foil, that you should buy a sheet of milled aluminum and polish it yourself.
And all I'm saying is that is unnecessary as the aluminum foil you likely have in your cabinets will do just as well without needing to be buffed or polished.
Mill finish is the result. Mill finish is the surface texture (or finish) of metal after it exits a rolling mill, extrusion die, or drawing processes, including foil, sheet, bar, plate, or structural shapes. This texture is usually rough and lacks lustre; it may have spots of oxidation or contamination with mill oil.
The oil is washed off in the rinse phase prior to drying and transfer to the tube.