UVB light keeps breaking

Status
Not open for further replies.

Drache613

BD.org Sicko
Staff member
Moderator
Hello,

I am sorry your tube bulb keeps breaking. How are you mounting it in
the tank? Can you show pictures of the tank setup so we can see how it
is sitting on or in the tank, or hanging?

Tracie
 

GalacticReptilian

Member
Original Poster
Drache613":171n4gvn said:
Hello,

I am sorry your tube bulb keeps breaking. How are you mounting it in
the tank? Can you show pictures of the tank setup so we can see how it
is sitting on or in the tank, or hanging?

Tracie

Here is a photo of my UVB hood, it's diagonal because of these strange notches in the center of the tank and I don't know what they are
101271-3744289056.jpg
 

GalacticReptilian

Member
Original Poster
The bulb has been replaced twice, and it always burns out within a few days. I would go to my local petsmart to buy the bulbs, replace the old one on my beardie's cage, and it would burn out in a matter of days.
 

kingofnobbys

BD.org Sicko
GalacticReptilian":37kjyuto said:
The bulb has been replaced twice, and it always burns out within a few days. I would go to my local petsmart to buy the bulbs, replace the old one on my beardie's cage, and it would burn out in a matter of days.

You need a sparky to check the reflector hood , it is likely the hood is faulty , may just be the wrong starter.

Try plugging into a different house power circuit …. might be an issue with circuit you are plugging into - again - you need to sparky to check the circuit.
 

CooperDragon

BD.org Sicko
Staff member
Moderator
If you're replacing the fixture it might make sense to get a T5 so you have higher output. The T8 is only effective at about 6-8'' while a T5 is stronger and optimal at about 12-14'' or so. You usually need to order them online. http://www.lightyourreptiles.com/22-t-5-ho-fixture-high-output-with-arcadia-d3-12-ho-bulb/

To answer your question, I've used the Zilla slimline fixture for an 18'' T8 and it has worked well. Just be sure to remove the clear plastic in front of the bulb because it will intercept all of the UVB.
 

GalacticReptilian

Member
Original Poster
CooperDragon":2nzz1wd0 said:
If you're replacing the fixture it might make sense to get a T5 so you have higher output. The T8 is only effective at about 6-8'' while a T5 is stronger and optimal at about 12-14'' or so. You usually need to order them online. http://www.lightyourreptiles.com/22-t-5-ho-fixture-high-output-with-arcadia-d3-12-ho-bulb/

To answer your question, I've used the Zilla slimline fixture for an 18'' T8 and it has worked well. Just be sure to remove the clear plastic in front of the bulb because it will intercept all of the UVB.
Thanks for the info
 

kingofnobbys

BD.org Sicko
GalacticReptilian":ddsdy7wc said:
If I give my beardie sunlight, how much will that help?
And which hood works best with the Reptisun 10.0 18" tube?

What is your geographic latitude ?
…. this will determine who much sunshine is needed to adequate UVA & UVB.
 
Status
Not open for further replies.

Members online

Still Needs Help

Latest resources

Latest posts

Latest profile posts

I just walked into my room and instead of looking at me, Swordtail's eyes darted directly to the ice cream drumstick I'm holding
Finally replaced Swordtail's substrate
I miss you so much, Amaris 💔
What is a quick way to warm up a cold beardie? His heating element went out overnight and now he's very cold.
Pearl Girl wrote on moorelori1966's profile.
i feel so sad reading your about me 😢

Forum statistics

Threads
156,022
Messages
1,256,909
Members
76,030
Latest member
Yunasmama
Top Bottom