Heat Losses for a 1.2m L x0.6m W x0.6m T viv

Discuss substrates, lighting, heating, enclosure building ideas, share enclosure photos, and talk about any other enclosure-related topics.

Heat Losses for a 1.2m L x0.6m W x0.6m T viv

Postby kingofnobbys » Sun Sep 03, 2017 3:44 am


Why do so many people insist in using glass vivs with effectively open tops ?
It's not because they are better except for the petshops who flog them to every noob reptile keeper who walks in the door.

Lets do some very basic heat transfer calculations ( conduction and natural convection , will ignore radiant heat and forced convection for simplicity ).


sides = 0.6m x 0.6m = 0.36m^2 ( 2 of these )
glass surfaces = 1.2m x 0.6m = 0.72m^2 ( 3 of these )

total glass surface area = 4x 0.72 = 2.88 m^2 = A

typical glass thickness = 6.5mm = 0.0065m = t

k value for ( soda ) glass = 0.96 W/m/K approx. @ 30 degC

Assume heat difference warm face to cold face = 35 degC to 10 deg C (very chilly)
==> DT = 25 deg C

Apply Fourier's Law of Heat Conduction loss , Q = kA(DT)/t = 0.96x2.88x25/0.0065 = 10633W

loss by free conductive through "open top" = hADT
h for air = 10 W/m^2K
A = 0.6x1.2= 0.72

so approx. heat loss by warm air escaping through lid = 10x 0.72x 25 = 180W



TIMBER ( 3/4 in Plywood , front glass door )

k plywood = 0.14 W/m/K

Area of timber
BTM + BACK + TOP all 0.6x1.2 = 3x0.72 m^2
Ends again 0.6x0.6 = 0.36m^2 each
total timber area = 4x0.72m^2

thickness = 0.75x0.025 =0.019m

Assume 35 degC inside , 10 degC outside , DT = 25 degC (Again)

Fouriers Law again : heat loss through timber surfaces = 0.14x(4x0.72)x25/0.019 = 537.6W

Heat loss through front doors ( simply assume equiv 1 sheet of glass 1.2x0.6 )
Fouries Law again : heat loss through front glass doors = 0.96x0.72x25/0.0065 = 2658W

Total for this viv = 3196W

clearly much more heat must be provided via a basking globe , heatpad , CHE or combination of these to maintain the temperature in the glass viv (which has an essentially open top) cf a timber viv with glass front doors.
The difference in heating required = 10813 - 3196 = 7617 W

Please feel free to comment and let me know if I've made any errors (I've been retired for nearly 20 years and am a wee bit rusty on my heat transfer).

Simple improvement for those stuck with a glass viv with a mesh lid , replace the mesh lid with a plywood lid .

The effect of a 3/4 in plywood lid :

Heat loss through timber lid (same dt, same thickness as above)
= 0.14x 0.72x 25/0.0188 = 134W

cf loss by natural convection through mesh lid = heat loss by warm air escaping through lid = 10x 0.72x 25 = 180W

==> 180-135 - 45W less heat lost simply by covering the top of the glass viv with a 3/4 in thick plywood lid.

Apply a buggerfactor (engineering jargon) to compensate for additional heat loss via radiant heat losses through the opening at the top of approx 1.5 for radiant loss through the opening = (1.5x180) - 135 = 135W !!

This is worth chasing especially in winter.

http://www.engineeringtoolbox.com/conve ... d_430.html
http://www.physicsclassroom.com/class/t ... t-Transfer
http://www.engineersedge.com/calculator ... _10047.htm
https://www.electronics-cooling.com/200 ... lat-plate/
https://www.physicsforums.com/threads/t ... ow.381511/
http://www.physicsclassroom.com/Class/t ... u18l1e.cfm
http://www.engineeringtoolbox.com/heat- ... d_113.html

k values
http://www.engineeringtoolbox.com/therm ... d_429.html

h value for air
http://www.engineeringtoolbox.com/heat- ... d_113.html
Last edited by kingofnobbys on Tue Sep 05, 2017 10:03 am, edited 1 time in total.
CBDs: Cleopatra & Caesar born 28Jan19.
Puff (RIP 10Dec15),Rex (RIP 16Mar17),Toothless (RIP 26Nov17).Peppa (RIP 22Mar19).
EBTSs : George & Mildred (born july 2010).
EWSs : , Fluffy (F) rescued injured by lawnwacker 14Nov17, Gutzy (F) rescued 27Sep19 - RIP 3Aug20 (est 12 yo), Wriggles (F) - injured rescue, over 8 yrs old, RIP 2Feb16 old age. Lucky juvenile (M) - cat attack rescue (lost r-eye, broken r-lower jaw), fatal SI RIP 21Jul2010.
BD.org Sicko
Posts: 12622
Joined: Tue May 12, 2015 10:56 pm
- Advertisement -
- Advertisement -

Re: Heat Losses for a 1.2m L x0.6m W x0.6m T viv

Postby CooperDragon » Sun Sep 03, 2017 5:07 pm

I bought mine because it was large, required no construction, was relatively affordable, and had front opening doors. At the time it made sense to get but I was a noob reptile keeper... I'd probably attempt to build my own if I had another shot at it but I'm pretty awful at that sort of thing. I leave the top off completely. It certainly doesn't hold in much heat but I don't expect it to. I just let the overhead lighting keep things in appropriate ranges. The power of my lighting is probably much more than would be needed for an enclosed wooden viv. I do like having the top open so I can raise the lighting as high as I want. That allows me to change the size of the basking area and keeps the lights well out of the way of climbing areas.
User avatar
Posts: 26362
Joined: Thu Mar 27, 2014 8:41 am
Location: Iowa City, IA

Re: Heat Losses for a 1.2m L x0.6m W x0.6m T viv

Postby charmander16 » Tue Sep 05, 2017 9:01 am

Wood is clearly better for larger vivs, but for smaller starter vivs glass makes sense. I think 40 gallon and less vivs could easily overheat with the typical bulbs used.

The larger the enclosure the more better insulation makes sense. I think 40 gallons is about as large as you would want an all-glass enclosure. You can of course make it work with larger all-glass enclosure's is just requires more heat.

But that's why most people do use "wood" (or wood like) material for larger vivs.

The real issue is not so much material, but rather starting people off on smaller vivs to begin with.

Ideally, people would start with a minimum of 8 square foot enclosures, because that's saves money in the long-run, but that's a more expensive way to start and it's easier for sellers to get people into the hobby at the lower starting cost and with a smaller, less imposing, viv.

And you see that here on the boards and it happened to me too. I think many fewer people would buy a bearded dragon if it was clear that the needed to start off with a minimum 4 foot long, $400-$500 (new including lights) setup.

Those starter setups cost about $150 to $200, which gets more people in the door, but really its $150 of wasted money because virtually everything needs to be replaced within 6 months.
Juvie Poster
Posts: 358
Joined: Tue Sep 27, 2016 10:45 pm
- Advertisement -
- Advertisement -

Return to Enclosures

Who is online

Users browsing this forum: No registered users